ina_jean: (Default)
posted by [personal profile] ina_jean at 07:00am on 18/08/2016 under , ,
When I joined the Agility Knitters group on Facebook I decided to actually knit an agility fence. I used a picture of a 'brick wall rug' from a book on knitting rugs as a basis but didn't think it worth spending any more money than I had to on actually buying a book for one pattern for a silly project.

The local Pound Shop (on Manford Way) has a good selection of cheap acrylic yarns, so I bought a ball of King Cole Super Chunky each in dark red (wine) bright red, orange (Mango) and grey (for the mortar rows). I needed an extra ball of a 'brick' colour so ordered a light brown (Sahara) from Wool Warehouse - whole lot came to about £10.

I wanted a chance to try out the size 6mm 'Symphonie' straight needles Frankie gave me as a Christmas present so cast on 30 stitches of the wine and knitted in moss stitch until the work was 'brick-sized' which turned out to be 13 rows. I threaded those onto a circular needle (with a 1m cable) and knitted three more in mango and red, finishing with a half-brick (15 stitches 13 rows)in wine. That gave me five separate pieces of knitting on the circular needle.

At this point I abandoned the straight needles and used the circular for the rest of the work. *Cast on with the grey and knitted the first 30 stitches of the first brick, Then made a stitch and used a 5mm crochet hook to crochet down the side of the brick, left a 4" loop (7" of yarn) at the bottom and crocheted up the side of the next brick. Looped the yarn back over the needle, then took a darning needle and (using a spare bit of DK yarn as a holder) threaded the loose loop through both sides of the crochet stitches to pull the two together. put the final bit of the loop over the rh needle, then picked up the stitch from the lh needle and continued in knit along the top of the second brick. Repeat process until the end of the row.

(I could have cast on a short length of grey and knitted the bricks together using fair isle technique - but there were going to be enough ends to sew in already without adding more!)

Wall in progress
Front and back of complete work before adding backing fabric.

Knit four rows of 'mortar' ending with yarn at same end as the start.

Cast on a contrast colour to the brick below and knit a second brick (or half-brick). Put the three 'mortar' stitches onto a holding thread or needle, and knit next brick in different colour. Continue to end then repeat from * above.

Make sure the crochet stitches are done on the front of the work and the grey mortar rows always begin at the same side of the work (it doesn't matter which end you start knitting the bricks from - the delights of circular needles!).

Stop when the work measures 4" shorter than the required fence height. (Five courses of bricks equal the 'small' KC height.) Complete the last line of 'mortar' then continue in garter stitch to make a 'coping' which will form the channel to put the bar of the fence through.

You could simply sew the top stitching back on itself, but I am sewing the whole thing to a backing fabric for extra strength - and to prevent too much stretching in the wash.)

Final version held on a broomstick (actually a Vileda mop handle!) on my jump wings.
Knit Jump edit 1
Mood:: 'silly' silly

Reply

From:
Anonymous( )Anonymous This account has disabled anonymous posting.
OpenID( )OpenID You can comment on this post while signed in with an account from many other sites, once you have confirmed your email address. Sign in using OpenID.
User
Account name:
Password:
If you don't have an account you can create one now.
Subject:
HTML doesn't work in the subject.

Message:

 
Notice: This account is set to log the IP addresses of everyone who comments.
Links will be displayed as unclickable URLs to help prevent spam.

August

SunMonTueWedThuFriSat
    1
 
2
 
3
 
4
 
5
 
6
 
7
 
8
 
9
 
10
 
11
 
12
 
13
 
14
 
15
 
16
 
17
 
18
 
19
 
20
 
21
 
22
 
23
 
24
 
25
 
26
 
27 28
 
29
 
30
 
31